A dead outlet is worth a call. So is a house that needs every wire replaced. We handle both, and everything between, for homeowners and rental property owners across Louisville and Boulder County. Whether the problem is a single circuit that stopped working or a panel that was never sized for the loads it now carries, the job starts the same way: a call, a scope, and a price before anything is scheduled.
We are available every day from 8:30 AM to 9:00 PM.
Call (720) 623-9659 and we will walk through what your situation involves.
We cover Louisville, the surrounding communities, and the rest of Boulder County with the same scope of electrical work described on this site.
A finished electrical job is not just a working circuit. When we complete a repair, an installation, or a panel upgrade, we test every affected outlet and circuit, confirm that breakers are labeled correctly, and document what was done. That record matters more than most people expect.
For a rental property, documentation of the electrical system's condition protects the owner when a tenant raises a concern. For a home sale, a buyer's inspector will check the panel, look at the GFCI and AFCI protection, and note any wiring that appears to have been modified without proper completion. A job done cleanly and documented correctly holds up to that review.
If we find something adjacent to the original scope that needs attention, we say so before touching it. The decision to address it stays with you.
Scheduling a service call is simple, and most requests are handled with a straightforward call and a confirmed appointment. We work around occupied homes and properties that need to stay in use, which matters when the work is in a kitchen, a hallway, or a room that cannot be cleared for a full day.
When a fault is urgent, the call still comes first. We scope the problem on the phone, determine what the visit needs to cover, and confirm what is available. We take short-notice work when the schedule allows, and prompt response is something we take seriously, even for last-minute electrical calls.
For rental properties with tenants in place, we confirm access arrangements on the call so the visit does not turn into a coordination problem at the door.
Recessed lighting is the most common indoor request we get, and for good reason. Replacing older ceiling fixtures with recessed LED trim changes how a room reads entirely, cuts heat output, and eliminates the fixture that collects dust above the dining table. We handle the wiring, the box work, and the switch or dimmer installation as a single visit.
Under-cabinet lighting in a kitchen is worth doing at the same time as any other kitchen electrical work, because the wiring runs are already open. Track lighting and pendant installations follow the same logic: if a circuit is already being modified, adding a fixture to it is a natural extension of the same visit.
Motion sensor lights, security fixtures, and landscape lighting circuits all come up regularly for Louisville properties. An exterior fixture that is not on a weatherproof circuit or a properly rated enclosure will fail faster than expected, especially through a Colorado winter. We wire outdoor lighting to handle the conditions it will actually face.
If the goal is security coverage on a driveway or around a garage, the fixture placement and the circuit routing are worth thinking through before the holes are drilled. We talk through that on the call.
An outdoor outlet that was added without a proper weatherproof enclosure is a fault waiting to happen. We install exterior-rated receptacles with in-use covers and run them on circuits with the correct GFCI protection. If an existing outdoor outlet has been exposed to weather without the right cover, replacement is the right move.
A ceiling fan that wobbles, hums, or has a light kit that flickers is usually a wiring or mounting issue rather than a fan problem. We install new fans, replace old ones, and add fan-rated boxes where the existing box was not designed to carry the load. If a separate dimmer and fan-speed control are needed at the switch, we handle that at the same visit.
Older Louisville homes, like older homes across this part of Colorado, were wired and paneled for loads that did not include EV chargers, modern kitchen appliances, and heat tape circuits running through a long winter. A panel that is undersized or simply worn out needs replacement, not repeated resets. We do load calculations before quoting so the new panel is sized for what is actually running in the home, not a round number. Subpanel installation for a detached garage or a finished basement follows the same process.
Many homes in this area still have battery-only detectors where hardwired interconnected units are now required. We wire them in as a standalone job or as part of a broader visit. Interconnected alarms mean that when one sounds, they all sound, which matters in a two-story home where the basement alarm would not otherwise be heard from the second floor.
Smart switches and dimmers are a straightforward upgrade when the existing wiring supports them. The common issue is that older wiring lacks a neutral wire at the switch location, which some smart switches require. We check the wiring before the switch is ordered and confirm compatibility. If a neutral needs to be run, that gets scoped and priced before any work starts.
Knob-and-tube wiring, where it still exists in older Louisville homes, is a replacement job. Aluminum branch-circuit wiring from the 1960s and 1970s requires remediation at the connections and, in some cases, a broader rewiring plan. Both situations are assessed on-site and explained clearly before any scope is agreed on. Partial rewiring covers specific rooms or circuits. Whole-home rewiring is a multi-day project, and it gets planned and priced that way.
The rate for any job is confirmed on the phone before anything is scheduled. We scope the work based on what you describe, explain what the visit involves, and give you a number you can make a decision with. There is no obligation to book before you have that figure.
What moves a quote is the actual condition of the work. What the fault turns out to be once it is traced, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change are the things that affect the final scope. If something on-site turns out to be different from what the call described, that gets explained before any additional work is done.
For larger projects like panel upgrades or whole-home rewiring, the quote reflects a full assessment of the load and the existing wiring. An EV charger or a hot tub often means checking the panel first, and if the panel needs attention before the circuit can be pulled, that gets folded into a single conversation rather than surfacing as a surprise later.
In a town like Louisville, the housing stock runs from mid-century ranch homes to newer construction. In ranch homes and split-levels, the panel is typically in the garage or a utility room. In two-story homes with a basement, it is often in the basement mechanical room. Knowing where the panel is before the visit means the diagnostic starts faster.
If access to the panel is blocked by storage, that is worth clearing in advance. A panel that cannot be fully opened adds time to any visit that involves circuit work, and it limits what can be tested safely.
Clear access to the panel and to the areas where the work is happening makes a real difference. For outlet or switch work, furniture or shelving in front of the receptacle adds time. For attic or crawl space work, the access point should be unobstructed. We confirm what access is needed on the call so the visit does not stall at the door. If you want to see the whole range first, try the services page covering electrical work.
We cover Louisville and the surrounding area across Boulder County. That includes Superior, Lafayette, Broomfield, and Paragon Estates, as well as Valmont and the communities in between. If you are just outside Louisville and wondering whether your address is covered, call and ask.
Boulder County properties run a wide range of ages and wiring situations, and that shapes the calls we get. Grounding and bonding issues, GFCI gaps, knob-and-tube replacement, and whole-home surge protection are all part of the regular work in this area. So are generator hookups and panel upgrades that have to account for the loads a cold-climate home puts on the system through a long winter.
If a commercial job is interrupted, we leave the site in a safe condition before we go. Exposed wiring is made safe, the panel is secured, and the status of the job is documented so the next visit picks up from a clear starting point. Nothing is left live and unprotected.
A subpanel is a good option when the main panel has capacity to spare and the goal is to add circuits to a specific area, such as a garage, a basement, or an addition, without running every circuit back to the main board. If the main panel is already at or near its limit, a subpanel does not solve the underlying capacity problem, and a service upgrade is the right conversation instead.
Louisville's housing stock includes homes built across several decades, and the wiring reflects that range. Knob-and-tube systems in the oldest homes, aluminum branch-circuit wiring from the 1960s and 1970s, and panels that were sized for loads that no longer match what the home runs are all situations we encounter regularly. Each one is assessed on-site before any scope is agreed on, and the findings are explained before work begins.
A kitchen renovation typically involves adding dedicated circuits for the range, the refrigerator, the dishwasher, and the countertop outlets, in addition to the lighting circuit. We assess the existing panel to confirm it can carry the added load, pull the new circuits, and rough-in the boxes before the cabinets and appliances go in. The trim-out happens after the finishes are in place.
A generator hookup involves a transfer switch that isolates the generator from the utility line, a dedicated circuit from the panel, and wiring that matches the generator's output capacity. The transfer switch is not optional: it is what keeps the generator from back-feeding the utility line during an outage, which is a safety requirement. We scope the panel capacity and the transfer switch size together on the call before anything is scheduled.
Yes. We assess what has already been done, identify what still needs to be completed, and quote the remainder of the job. If any of the existing work is not correct, we will tell you before proceeding, because finishing a job on top of unsafe work is not something we will do without addressing the underlying problem first.
A single outlet that stopped working is worth a call. So is the flickering light that has been easy to ignore. The same number that handles a whole-home rewiring quote handles a one-outlet repair, and the process is the same: scope it on the phone, confirm the price, schedule the visit.
Call (720) 623-9659.
We are available every day from 8:30 AM to 9:00 PM. We power your home. We protect your circuits. We earn the call.
Electrical service reaches these neighboring areas too: Superior, Lafayette, Gunbarrel.
See our full area list.
We handle the full range of residential and commercial electrical work across Louisville and Boulder County, from a single tripped breaker to a complete service upgrade. Every job starts the same way: a call, a scope, and a price before anything is scheduled. The table below covers what each service includes and who it fits best. Call for a quote and we will walk through the details on the phone.
| Type of Work | Scope of Work | Common Situations | Worth Knowing |
|---|---|---|---|
| Wiring & Circuit Installation | Rough-in for renovations and additionsKnob-and-tube and aluminum wiring remediationNew circuit runsRewiring for updated code compliance | Older homes being updated and new construction or addition projects | Aluminum branch-circuit wiring from the 1960s and 1970s requires connection remediation, not just a visual inspection. |
| Ceiling Fan Installation | New fan wiring and mountingFan and light kit combination installsOld fan swap-outsBox and wiring support check | Rooms that need better air circulation or a fixture upgrade | A ceiling fan box rated for fan support is different from a standard light fixture box. We check before mounting. |
| Electrical Panel & Service UpgradesMost Popular | Load calculation and panel sizing100-amp to 200-amp service upgradeFuse box to breaker panel conversionSubpanel installation for garages and additions | Homes adding EV chargers, heat tape circuits, or heavy appliances to an older service | Cold-climate homes in Boulder County run more sustained electrical load than the same square footage would in a milder region, and older panels were not sized for it. |
Call (720) 623-9659 to go through the job on the phone and get a price before anything is scheduled. We are available every day from 8:30 AM to 9:00 PM.
(720) 623-9659