When electrical work is done right, it leaves a record. A panel that was properly upgraded, a circuit that was pulled to code, GFCI protection installed where it belongs - those things show up when a home inspector walks through, when an insurance carrier asks questions, and when a property changes hands. For homeowners and landlords in Erie, that record matters more than most people think about until the moment it is needed.
We handle the full range of residential and commercial electrical work in Erie and the surrounding area. From a single dead outlet to a whole-home rewiring project, the process starts the same way: a call, a scope on the phone, and a price before anything is scheduled. We are available every day from 8:30 AM to 9:00 PM.
The jobs below are the ones that come up regularly in a city this size. Some are repairs. Some are upgrades. Some are new installations for a home that has changed. Each one starts with understanding the situation, not just the symptom.
A panel that was installed for a smaller load than the home now carries is not a failure waiting to happen in some distant future. It is already working harder than it should. Breakers that trip under normal use, a panel that runs warm, or a fuse box that has never been converted to breakers are all situations worth addressing. We do load calculations before quoting a replacement so the new panel is sized for what the home actually runs, not a number pulled from a general range.
Recessed and LED lighting upgrades are among the most common requests we handle. Swapping older fixtures for recessed LED trim changes how a room reads and cuts heat output from the ceiling. We also wire and install track lighting, pendants, chandeliers, and under-cabinet lighting. Where a new fixture location needs a circuit run or a box added, we handle that at the same visit.
GFCI protection is required at outlets near water, and AFCI protection is required on bedroom and living area circuits in homes built or substantially renovated under current code. Older homes in Erie frequently have neither where they belong. An outlet that trips and will not reset, or one that has never had protection at all, is a straightforward fix, but it is worth doing correctly rather than just resetting what is there.
Battery-only detectors are common in older homes, but interconnected hardwired units are now required in many situations. When one alarm sounds, they all sound. We wire them in as a standalone job or as part of a broader inspection visit. If the existing wiring can support interconnected units, we confirm that before the installation starts.
A new appliance, a hot tub, or a workshop load that gets added to an existing circuit is asking that circuit to carry more than it was designed for. Each of those runs better and more safely on its own dedicated line. An EV charger or a hot tub often means checking the panel first, because the dedicated circuit is only half the job if the panel is already near capacity. We scope the panel and the circuit together so the installation is complete, not just connected.
Ceiling fan installation fits here too. We wire new fans, replace old ones, and add fan-rated boxes where the existing box will not support the fixture.
Commercial electrical work is planned differently from residential work. A business that has to stay open during a repair or an upgrade needs the job sequenced so the right circuits stay live while the work happens around them. We handle that planning on the front end, before anything is scheduled.
Out-of-hours work is available for commercial sites where daytime access is not practical. For multi-tenant buildings and light industrial spaces, we coordinate with whoever is on-site and confirm access before the visit. Panel upgrades, subpanel installation, commercial lighting, and circuit work for tenant improvements all follow the same process: scope the job, confirm what stays live, and plan the sequence before we start.
Scheduling a service call is simple, and we handle short-notice requests when the schedule allows. If a fault will not keep, call and describe what you are seeing. We take urgent faults seriously and work through the schedule to get there when it matters.
For tenants and businesses that have to stay open, we ask about the situation on the call. If a circuit needs to come down during the repair, we plan around the parts of the property that cannot go dark. That conversation happens before the visit, not after we arrive.
We are available every day from 8:30 AM to 9:00 PM.
Call (720) 623-9659 and describe what is happening.
We scope the job on the phone, give you a price, and confirm what the visit covers before anything is booked.
A quote covers the scope as it is understood on the call. Three things move it after the visit starts: what the fault actually turns out to be once it is traced, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change being made. Those are not surprises, they are the realities of electrical work in homes where the wiring is not always documented and the walls have not been opened recently.
If the scope changes on-site, that gets explained before any additional work is done. You are not committed to work beyond what was quoted without a conversation first. The price for the original scope is confirmed on the call. What the job actually involves is explained before anything starts.
Aluminum wiring, knob-and-tube systems, and panels that were never brought up to current standards all affect what a job takes. We assess what is there and explain the options before the work begins. An electrical inspection before a renovation or a sale documents the condition of the system and identifies what needs attention, and that gives everyone a clear picture before the scope is agreed on.
No guesswork. No shortcuts. No loose ends.
Not every power problem sits inside the home's wiring. A complete loss of power, a partial outage affecting only some circuits, or a fault that traces back to the service entrance may sit on the utility's side of the meter rather than ours. We work through the diagnostic to find where the fault actually lives.
If the problem is on the utility's side, we tell you that clearly and explain what the next step looks like. That means contacting the utility and describing what was found. We do not leave a customer with an unexplained outage and no direction. The diagnostic tells us where the fault is, and we explain what that means for who handles it from there. The range of work covered is explained on our electrical repair services page.
We handle electrical work throughout Erie and the communities around it in Weld County and the broader northern Front Range. That includes Lafayette, Dacono, Frederick, Broomfield, and Gunbarrel. Residential and commercial calls from across the area are covered equally.
If you are just outside Erie and wondering whether your address is in range, call and ask. We will confirm it on the phone.
We power your home. We protect your circuits. We earn the call.
We need clear access to the panel to work safely. If the area around the panel is blocked, clearing it before the visit saves time and keeps the job on schedule. If you are not sure what access is needed, ask when you call and we will describe what the visit requires.
Yes. Every circuit and device involved in the job is tested before we leave. For outlet work, that means checking for correct wiring, polarity, and GFCI function where applicable. For panel work, it means verifying every circuit is live and correctly labeled before the panel cover goes back on.
Aluminum branch-circuit wiring was common in homes built during the 1960s and 1970s, and it requires specific remediation at the connections rather than standard copper repair methods. If a home in that era has not had its wiring assessed, it is worth mentioning on the call so the visit is scoped correctly from the start. We assess what is there and explain the options before any work begins.
Underground runs to outbuildings are the standard approach because overhead wiring has its own clearance and support requirements that are harder to meet in most residential settings. The depth and conduit requirements for a buried cable depend on the wiring method used. We confirm what applies to the specific run before the trench is dug.
An inspection report documents the condition of the panel, the wiring, the outlets, the switches, and the protective devices throughout the property. It notes what is working correctly, what is not, and what falls outside current code requirements. It is a factual record of what was found, not a sales document.
Permit requirements depend on the scope of the work and whether it involves the service entrance, new circuits, or changes to the panel. We confirm what applies to the specific job before anything is scheduled, so there are no open questions about compliance after the work is done. If a permit is needed, that gets factored into the scope on the call.
You do not need to know what is wrong before you call. Describing what you are seeing is enough. A breaker that keeps tripping, a light that will not come on, a smell near the panel, an outlet that stopped working, a circuit that needs to be added for something new.
Call (720) 623-9659, tell us what is happening, and we will work through the rest from there. We are available every day from 8:30 AM to 9:00 PM.
Electrical work in the surrounding towns: Lafayette, Dacono, Frederick, Gunbarrel, Louisville.
You can browse our full area list.
We handle the full range of residential and commercial electrical work across Erie and Weld County, from a single tripped breaker to a complete service upgrade. Every job starts the same way: a call, a scope, and a price before anything is scheduled. The table below covers what each service includes and who it fits best. Call for a quote and we will walk through the details on the phone.
| Type of Work | Scope of Work | Common Situations | Worth Knowing |
|---|---|---|---|
| Heat Tape Installation | Dedicated circuit for self-regulating heat tapeWiring to roof edge and pipe run locationsLoad calculation for the system being usedConnection and circuit verification | Erie homes with roof ice dam problems or vulnerable pipe runs in unheated spaces | Self-regulating heat tape still needs a correctly sized dedicated circuit. Sharing a circuit with other loads is a common installation mistake. |
| Whole-Home Surge Protection | Panel-level surge device installationProtection for all circuits from a single pointGuards against utility-line voltage spikesStandalone or combined with panel work | Homes with sensitive electronics, home offices, or recently upgraded appliances | Voltage spikes from equipment cycling inside the home can cause damage just as utility-side surges do. |
| Electrical Panel & Service UpgradesMost Popular | Load calculation and panel sizing100-amp to 200-amp service upgradeFuse box to breaker panel conversionSubpanel installation for garages and additions | Homes adding EV chargers, heat tape circuits, or heavy appliances to an older service | Cold-climate homes in Weld County run more sustained electrical load than the same square footage would in a milder region, and older panels were not sized for it. |
Call (720) 623-9659 to go through the job on the phone and get a price before anything is scheduled. We are available every day from 8:30 AM to 9:00 PM.
(720) 623-9659