Northglenn Electrical Company handles the full range of residential and commercial electrical work across Northglenn and Adams County. Whether you have a dead outlet that stopped working overnight, a breaker panel that needs replacing, or a new EV charger circuit to run, we take the call and get it scheduled. Our work covers repairs and troubleshooting, panel upgrades, wiring and rewiring, lighting, ceiling fans, dedicated appliance circuits, whole-home surge protection, backup generator hookups, and EV charger installation. We are available every day from 8:30 AM to 9:00 PM, including weekends.
No guesswork. No shortcuts. No loose ends.
Flickering lights and warm outlets are warning signs, not quirks. If something in your home's electrical system has been acting up, that is worth a call. We scope the job on the phone before anything is scheduled, and the wiring is done properly, start to finish.
Don't let a small wiring issue turn into a fire risk, because most electrical problems that seem minor are pointing at something real underneath. A breaker that trips repeatedly is not just an inconvenience. It is telling you the circuit is carrying more load than it should, or that there is a fault somewhere in the wiring. We trace the cause before we talk about a fix.
A diagnostic visit covers the full picture. We check the outlet, the circuit, and the panel. For dead outlets, we test for GFCI trips upstream, check for loose connections, and look for signs of burning or arcing at the receptacle. Burnt or sparking outlets get replaced, not reset. GFCI and AFCI outlets and breakers are installed where the circuit calls for them, whether that is a bathroom, a kitchen, or a bedroom circuit that needs arc-fault protection.
Flickering lights, dimming when an appliance kicks on, or lights that go out without warning all get the same treatment: we find the source. Sometimes it is a loose wire at the fixture. Sometimes it is a connection at the panel. We do not guess at it.
A breaker that keeps tripping is a warning worth heeding.
Good electrical work isn't complicated, it's just done right, and most outlet, switch, and lighting jobs are straightforward when the wiring behind them is handled correctly. We install and replace the full range: standard outlets, GFCI outlets, AFCI outlets, and USB combination receptacles. If an outlet is ungrounded, we address the grounding and bonding at the same time so the replacement is correct, not just cosmetic.
Switch work covers standard single-pole switches, three-way switch replacements, and dimmer installation. If a dimmer is flickering or buzzing, the switch and the fixture need to be matched correctly. We handle that as part of the installation.
For lighting, we wire and install recessed and can lights, track lighting, under-cabinet lighting, and interior fixture replacements. Outside, we install motion sensor lights, landscape wiring, and exterior fixture replacements for security and visibility. We protect your floors and finishes while we work, which matters on finished rooms where lighting work means going above the ceiling or behind walls.
Ceiling fan installation and replacement rounds out this section. We wire new fans, swap out old ones, and install ceiling fans with light kits where the box and wiring support it.
Dead outlets usually have a simple cause worth finding.
Choosing the right electrical fix is easier than it sounds, especially when the starting point is a panel that is undersized or simply worn out. A 100-amp service that made sense for a home built decades ago may not carry the load of a modern household running heat tape circuits, an EV charger, and a full appliance lineup at the same time. We handle the full service upgrade: load calculation, service-entrance work, meter coordination, and installation of the new breaker panel.
Fuse box to breaker panel conversions come up regularly in older Adams County homes. If the home still has a fuse box, that is a replacement job, not a repair. We assess the existing service, determine the right panel size, and handle the permit and code compliance work as part of the project.
Electrical panel repair, when a breaker is failing or a bus connection is loose, is handled separately from a full replacement. We diagnose first and tell you what the panel actually needs before any work is scheduled.
Subpanel installation for a detached garage, a workshop, or an addition is also within scope. If the main panel has the capacity, we run the feeder and install the subpanel where the load requires it.
Appliances that draw heavy loads need their own circuit. That covers refrigerators, washers, dryers, ranges, dishwashers, and workshop equipment. A dryer or range also needs a 240-volt outlet, and we run the circuit and install the outlet as a single job. If the panel does not have the capacity, that conversation happens before the circuit is pulled.
Older homes in the area carry a range of wiring situations. Knob-and-tube wiring, where it still exists, is a replacement job. Aluminum wiring from the 1960s and 1970s requires remediation at the connections and, in some cases, a broader rewiring plan. We assess what is there and explain the options.
Renovation and addition work brings its own electrical scope. Kitchen remodels, bathroom additions, basement finishing, garage wiring, and shed circuits all require rough-in work that coordinates with the other trades. Bathroom circuits include GFCI protection and, where needed, exhaust fan wiring. We handle the electrical side from rough-in through final trim.
We'll get the job wired and finished.
Northglenn winters are hard on homes and on electrical systems. The Front Range gets extended cold snaps, ice storms, and heavy snow loads that create electrical demands that simply do not come up in milder parts of the country. The three services below address what comes up most often here when the weather turns.
When a winter storm knocks out power on the Front Range, outages can run for hours or days. A backup generator is only useful if it is wired correctly. We handle the generator hookup: a dedicated circuit from the panel, a transfer switch that isolates the generator from the utility line, and the connection that lets the generator carry the loads you need. We work with both standby and portable generator setups and size the transfer switch to match what the generator can handle.
Cold-climate homes in Adams County run more electrical load than the same square footage would in a warmer region. Heat tape circuits, plug-in space heaters, and EV chargers added over time push older panels past what they were designed to carry. Aging housing stock in the area means many panels were installed when those loads did not exist. A load calculation shows what the panel is actually carrying and what a replacement needs to support. We handle the full upgrade with code-compliant wiring throughout.
Roof ice dams and frozen pipes are routine winter problems on the Front Range. Heat tape keeps vulnerable pipe runs and roof edges from freezing, but the electrical side of the installation matters as much as the tape itself. Self-regulating heat tape systems need a dedicated circuit and proper wiring to operate safely. We run the circuit, wire the connection, and make sure the installation meets the load requirements for the system being used. This is circuit and hookup work, not a product sale.
Not every electrician works the same way, and EV charger installation is a good example of where the details matter. A Level 2 home charger runs on a dedicated 240-volt circuit. Before that circuit is pulled, we check panel capacity and confirm the breaker size the charger requires. If the panel needs a slot or a capacity upgrade, we address that first. The result is a charger circuit that handles the load it was designed for.
Whole-home surge protection installs at the panel and covers every circuit in the house from a single point. It protects appliances, electronics, and wiring from voltage spikes that come in through the utility line or from equipment cycling on and off inside the home. It is a straightforward panel-level installation, and we handle it as a standalone job or as part of a larger panel project.
We take prompt response seriously, even for last-minute electrical calls, and EV charger and surge protection requests are scheduled the same way as any other service call.
Property managers, landlords, and home buyers all have reasons to want a clear picture of what a home's electrical system actually looks like. We conduct electrical safety inspections that cover the panel, the wiring, the outlets, and the fixtures. The findings are explained before any repair work is discussed.
For rental properties, an inspection documents the condition of the electrical system and identifies GFCI and AFCI protection gaps, grounding issues, and any code violations that need correction. For home purchases, an inspection before closing gives the buyer a clear view of what the electrical system will need. We also handle the repair side: code violation corrections, failed inspection follow-up, and work needed to bring a system up to current standards.
Hardwired smoke detector and carbon monoxide detector installation is part of this scope. Many older homes in the area have battery-only detectors where hardwired interconnected units are now required. We wire them in as a standalone job or as part of a broader inspection and repair visit.
No guesswork. No shortcuts. No loose ends.
We handle electrical work across Northglenn and the surrounding communities in Adams County and the northern Denver metro. That includes Thornton, Westminster, Federal Heights, Commerce City, Brighton, Broomfield, and Arvada. Residential and commercial customers across the area are covered equally.
We are available every day from 8:30 AM to 9:00 PM. Whether the call is for a single outlet repair or a full panel replacement, the process starts the same way: a call, a scope, and a price before anything is scheduled.
Scheduling a service call is simple, and pricing works the same way. When you call, we go through the job on the phone. You get the price before anything is booked, and the quote covers the scope so you know what the visit includes. There are no ranges pulled from thin air. The price reflects what the job actually involves.
Electrical work varies in cost because the jobs vary. A single outlet replacement is a different scope from a panel upgrade or a whole-home rewiring project. What stays consistent is how pricing is handled: clearly, before the work starts, with the scope explained so you know what you are getting.
Call for a quote at (720) 623-9659. We are available every day from 8:30 AM to 9:00 PM.
The visit starts with a diagnostic: we look at the symptom, trace it to the source, and explain what we found before any work begins. Once the scope is confirmed and agreed on, the repair or installation is carried out, connections are tested, and the circuit is verified before we leave. We protect your floors and finishes while we work and leave the site clean.
Breakers that trip frequently, a panel that feels warm to the touch, a burning or plastic smell near the panel, and lights that dim when a large appliance starts are all signs worth taking seriously. An older fuse box that blows fuses repeatedly is pointing at the same problem. These symptoms mean the panel is working harder than it should, and a diagnostic call is the right next step.
A burning smell near an outlet usually means arcing or overheating at the connection, which can be caused by a loose wire, a failing outlet, or a circuit that is carrying more load than it was designed for. Near the panel, it can indicate a loose bus connection or a failing breaker. Either location warrants a call right away rather than waiting to see if it goes away.
A burning smell, sparking from an outlet or panel, a breaker that will not reset, or any sign of heat or scorch marks near wiring or devices are all situations that should not wait. Power loss to part or all of the home after a storm or a sudden event also warrants a prompt call. We are available every day from 8:30 AM to 9:00 PM and take urgent faults seriously.
A Level 2 home charger runs on a dedicated 240-volt circuit. The installation starts with a panel capacity check to confirm the breaker size the charger requires and that the panel has room for the added load. From there, we run the circuit to the garage or driveway location and install either a hardwired connection or a NEMA 14-50 outlet depending on the charger type. If the panel needs a slot or a capacity upgrade first, that is handled before the circuit is pulled.
An inspection makes sense before buying or selling a property, after a renovation, when a rental unit changes tenants, or when a home has older wiring that has not been evaluated recently. It covers the panel, the wiring, grounding and bonding, and GFCI and AFCI protection throughout the home. The findings are explained before any repair work is discussed.
Knob-and-tube wiring, where it still exists, is a replacement job rather than a repair. Aluminum branch-circuit wiring from the 1960s and 1970s requires remediation at the connections and, in some cases, a broader rewiring plan. Both situations are assessed on-site and explained clearly before any scope is agreed on. Neither is unusual in Adams County housing stock.
Someone with access to the property and knowledge of where the panel is located needs to be present, or arrangements need to be made for access. For commercial properties and rental units, the property manager or a designated contact can fill that role. Let us know the situation when you call and we will work out what is needed.
Clear access to the panel is the most important thing. If the work involves outlets, fixtures, or circuits in specific rooms, those areas should be accessible and not blocked by furniture or stored items. For attic or crawl space work, access points should be unobstructed. The more accessible the work area, the faster the diagnostic and the repair go.
Flickering that happens across the whole house often points to a loose connection at the service entrance or the panel. Flickering in one room or on one circuit is more likely a loose wire at a fixture or junction box, or a failing switch or dimmer. Dimming when a large appliance starts up usually means the circuit is undersized or the panel is near capacity. Each pattern points somewhere different, and we trace it before recommending a fix.
A dedicated circuit means a single breaker in the panel feeds only that one outlet or appliance, with no other loads sharing the line. Ranges, dryers, refrigerators, dishwashers, and workshop equipment all run more reliably and safely on their own circuit. The job involves pulling the circuit from the panel to the appliance location and installing the correct outlet for the load. If the panel does not have the capacity, that conversation happens before the circuit is pulled.
A single outlet or switch repair is usually a short visit once the diagnostic is complete. A panel upgrade runs longer because it involves service-entrance work, load calculations, and testing every circuit after the new panel is in. Whole-home rewiring is a multi-day project. When you call, we give you a realistic time estimate based on the scope, not a number pulled from a general range.
When you need an electrician in Northglenn or anywhere in Adams County, Northglenn Electrical Company is available to take the call and get the work on the schedule. From repairs and panel upgrades to generator hookups and EV charger circuits, we handle the full scope of residential and commercial electrical work.
We power your home. We protect your circuits. We earn the call.
Call (720) 623-9659 for a quote. We are available every day from 8:30 AM to 9:00 PM.
We handle the full range of residential and commercial electrical work across Northglenn and Adams County, from a single tripped breaker to a complete service upgrade. Every job starts the same way: a call, a scope, and a price before anything is scheduled. The table below covers what each service includes and who it fits best. Call for a quote and we will walk through the details on the phone.
| Type of Work | Scope of Work | Common Situations | Worth Knowing |
|---|---|---|---|
| Heat Tape Installation | Dedicated circuit for self-regulating heat tapeWiring to roof edge and pipe run locationsLoad calculation for the system being usedConnection and circuit verification | Northglenn homes with roof ice dam problems or vulnerable pipe runs in unheated spaces | Self-regulating heat tape still needs a correctly sized dedicated circuit. Sharing a circuit with other loads is a common installation mistake. |
| Lighting Installation | Recessed and track lightingExterior and motion sensor fixturesUnder-cabinet and landscape wiringInterior fixture replacement | Renovation projects, security lighting upgrades, and finishing a new space | Outdoor lighting on the Front Range takes a beating from freeze-thaw cycles, so fixture and junction box choice matters. |
| Electrical Repairs & Troubleshooting | Dead outlets and failed switchesTripping breakers traced to sourceArcing or burning connectionsCircuit-level fault diagnosis | Any home or property with an unexplained electrical symptom | A warm outlet or a breaker that will not reset is worth a prompt call, not a wait-and-see approach. |
| Whole-Home Surge Protection | Panel-level surge device installationProtection for all circuits from a single pointGuards against utility-line voltage spikesStandalone or combined with panel work | Homes with sensitive electronics, home offices, or recently upgraded appliances | Voltage spikes from equipment cycling inside the home can cause damage just as utility-side surges do. |
| Outlet & Switch Installation | Standard, GFCI, and AFCI outletsDimmer and three-way switch replacementUSB combination receptaclesGrounding and bonding at the box | Homeowners adding outlets, replacing outdated devices, or correcting ungrounded receptacles | Replacing an ungrounded outlet without addressing the grounding behind it is a cosmetic fix, not a real one. |
| Wiring & Circuit Installation | Rough-in for renovations and additionsKnob-and-tube and aluminum wiring remediationNew circuit runsRewiring for updated code compliance | Older homes being updated and new construction or addition projects | Aluminum branch-circuit wiring from the 1960s and 1970s requires connection remediation, not just a visual inspection. |
| Electrical Safety Inspections | Panel and wiring condition assessmentGFCI and AFCI protection reviewGrounding and bonding checkFindings explained before any repair is discussed | Home buyers, landlords, and owners of older properties with uninspected wiring | An inspection before closing gives buyers a clear picture of what the electrical system will need before any repair decisions are made. |
| Ceiling Fan Installation | New fan wiring and mountingFan and light kit combination installsOld fan swap-outsBox and wiring support check | Rooms that need better air circulation or a fixture upgrade | A ceiling fan box rated for fan support is different from a standard light fixture box. We check before mounting. |
| Backup Generator Installation | Transfer switch installationDedicated generator circuit from panelPortable and standby generator hookupsLoad sizing for the transfer switch | Front Range homeowners who lose power during winter storms and need reliable backup | A transfer switch isolates the generator from the utility line, which is a code requirement and a safety necessity. |
| Dedicated Appliance Circuits | 240-volt circuits for ranges and dryersRefrigerator and dishwasher circuitsWorkshop and garage equipment circuitsCorrect outlet installed with the circuit | Homeowners adding a major appliance or workshop equipment to an existing home | If the panel does not have capacity for the added circuit, that conversation happens before anything is pulled. |
| Electrical Panel & Service UpgradesMost Popular | Load calculation and panel sizing100-amp to 200-amp service upgradeFuse box to breaker panel conversionSubpanel installation for garages and additions | Homes adding EV chargers, heat tape circuits, or heavy appliances to an older service | Cold-climate homes in Adams County run more sustained electrical load than the same square footage would in a milder region, and older panels were not sized for it. |
| Breaker & Fuse Repair | Failing or stuck breakers replacedFuse box assessmentBus connection checksPanel-level fault isolation | Homes where a breaker trips repeatedly or a fuse blows without a clear cause | A breaker that trips on a lightly loaded circuit often points to a wiring fault, not just an overload. |
What are the signs that a home needs a panel or service upgrade?
The clearest signs are breakers that trip under loads they should handle, a panel that feels warm to the touch, a burning or plastic smell near the enclosure, and lights that dim noticeably when a large appliance starts. A fuse box that blows fuses repeatedly is pointing at the same problem. Homes that have added EV chargers, heat tape circuits, or major appliances over time without a panel review are worth a diagnostic call even without obvious symptoms.
What causes a breaker to trip repeatedly?
Repeated tripping usually means one of three things: the circuit is carrying more load than it was designed for, there is a wiring fault somewhere on the circuit, or the breaker itself is failing. An overloaded circuit is the most common cause, but a breaker that trips on a lightly loaded circuit is more likely pointing at a fault in the wiring or at the connections. We trace the cause before recommending a fix.
Is electrical work permitted and inspected?
Permit and inspection requirements depend on the scope of the work and the jurisdiction. Panel replacements, service upgrades, and new circuit installations typically require a permit through the local authority. We handle the permit and inspection coordination as part of the project so the work is documented and signed off correctly.
Faults Traced Before Anything Is Replaced
We find the source of the problem before we talk about a fix. Replacing parts without a diagnosis is how a repair visit turns into a second visit for the same symptom.
How do I know if my home is ready for added electrical load, like an EV charger or a new appliance?
The starting point is a load calculation on the existing panel. That tells us what the panel is currently carrying and whether it has the capacity to support the added circuit. If the panel is at or near capacity, the upgrade conversation happens before the new circuit is pulled. We do not run a circuit into a panel that cannot support it.
How are emergency electrical faults handled?
A burning smell, sparking from an outlet or panel, a breaker that will not reset, or visible scorch marks near wiring or devices are all situations that should not wait. We are available every day from 8:30 AM to 9:00 PM and take urgent faults seriously. If the situation involves active sparking or smoke, shut off the main breaker if it is safe to do so and call before attempting anything else.
Why would an outlet or switch stop working without tripping a breaker?
A dead outlet that has not tripped a breaker is often caused by a GFCI outlet upstream on the same circuit that has tripped and cut power to everything downstream. It can also be a loose wire at the outlet or at a junction box on the circuit. Less commonly, it is a failing outlet that has lost its internal connection. We test for the upstream GFCI first, then trace from there.
Code-Compliant Work on Every Job
Panel upgrades, new circuits, and GFCI installations are handled to current code requirements. Where a permit and inspection are required, we coordinate that as part of the project.
What is GFCI protection and where is it required?
A GFCI outlet or breaker monitors the current flowing through a circuit and cuts power within milliseconds if it detects an imbalance that could indicate a shock path to ground. Current code requires GFCI protection in bathrooms, kitchens, garages, outdoor locations, and anywhere near water. Older homes often have these areas unprotected. We install GFCI outlets and breakers where the circuit calls for them, whether as part of a repair or as a standalone upgrade.
What does surge protection at the panel actually cover?
A whole-home surge protector installs at the main panel and intercepts voltage spikes before they reach any circuit in the house. It covers the refrigerator, the washer and dryer, the HVAC electrical supply, home office equipment, and anything else on the home's wiring. It does not replace point-of-use surge strips for sensitive electronics, but it handles the larger spikes that strip-level protection is not rated for. We install it as a standalone job or as part of a panel upgrade.
Clean and Respectful Workmanship
We protect your floors and finishes while we work and leave the site clean when the job is done. That applies to a single outlet replacement as much as it does to a full panel upgrade.
When does it make sense to call an electrician rather than attempt a DIY fix?
Replacing a light bulb or resetting a GFCI outlet is straightforward. Anything that involves opening a panel, running a new circuit, replacing a breaker, or working inside an outlet or switch box is a different situation. The panel in particular is energized at the service entrance even when the main breaker is off, and the consequences of a mistake there are serious. If the symptom is a burning smell, sparking, or heat near wiring, that is a call, not a project.
What is involved in a backup generator hookup, and why does the transfer switch matter?
A generator hookup involves running a dedicated circuit from the panel to the generator location and installing a transfer switch that disconnects the home from the utility line when the generator is running. The transfer switch is not optional. Without it, power from the generator can feed back onto the utility line, which creates a serious hazard for anyone working on that line during an outage. We size the transfer switch to match what the generator can handle and wire the connection to code.
How does grounding and bonding affect safety in an older home?
Grounding gives fault current a safe path back to the panel so a breaker can trip and clear the fault. Bonding ties metal components together so they stay at the same electrical potential and do not create a shock path between them. Older homes frequently have ungrounded outlets, missing ground wires in the wiring, or bonding gaps at the panel. These are not always obvious from the outside of an outlet, which is why an inspection that goes beyond the surface matters.
Call (720) 623-9659 to go through the job on the phone and get a price before anything is scheduled. We are available every day from 8:30 AM to 9:00 PM.
(720) 623-9659